All Categories
Fiber Optomechanics

FILTER PRODUCTS

Select a category above to apply technical filters
  1. Home
  2. Fiber Optics
  3. Fiber Optomechanics

Page 13 - Fiber Optomechanics

Miniature Fiber Rotary Joints MicroJx Series
Princetel
Add to watch list
Miniature Fiber Rotary Joints MicroJx Series
MJX series Fiber Optic Rotary Joints (FORJs) are extremely compact. So small they can even be used in the middle of fluid flows. They are the world\'s smallest and lightest. They feature very low insertion loss and impressive return loss performance. Model MJXA typically yields return loss figures higher than 60 dB. The standard ...
Data Sheet
Single-Channel Fiber Optic Rotary Joints R-series
Princetel
Add to watch list
Single-Channel Fiber Optic Rotary Joints R-series
The R series Single-channel (SM or MM) rotary joints offer many variations. The rugged body allows fiber pigtail, ST, or FC receptacles on either the rotor or the stator side. There can be total nine different configurations to fit the need exactly. The standard base models are RPT, RFC, and RST for pigtails, FC/PC, and ST/PC ...
Data Sheet
16283 Ferrule PRIZM MT Elite 4x12F Multimode 850 AR
US Conec
Add to watch list
16283 Ferrule PRIZM MT Elite 4x12F Multimode 850 AR
US Conec’s novel PRIZM® MT expanded beam ferrule technology has revolutionized high density point-to-point interconnects by merging low cost multi-fiber ferrule component design with no-polish fiber termination processing. The PRIZM® MT ferrule combines US Conec’s industry leading high-precision fiber alignment ...
Data Sheet
13950 Ferrule PRIZM LightTurn 12F Multimode Reduced Window
US Conec
Add to watch list
13950 Ferrule PRIZM LightTurn 12F Multimode Reduced Window
Designed as a miniature detachable connector for board mounted parallel optic modules, the PRIZM® LightTurn® connector solution provides passive alignment and novel retention features allowing multiple re-matings perpendicular to the printed circuit board. The PRIZM® LightTurn® connector consists of a multi-fiber ...
17185 MT Ferrule With Boot 12F Multimode MT Elite Dimple
US Conec
Add to watch list
17185 MT Ferrule With Boot 12F Multimode MT Elite Dimple
US Conec manufactures durable, composite, Polyphenylene Sulfide (PPS) based thermoplastic ferrules available with up to 72 fiber holes that terminate 125 micrometer optical fiber. The ferrules are used in conjunction with US Conec’s industry hailed, MTP® brand, MPO type connectors; however, they are also suitable for custom ...
Data Sheet
17181 MT Ferrule With Boot 24F Single-Mode APC Pre-Angled 20N
US Conec
Add to watch list
17181 MT Ferrule With Boot 24F Single-Mode APC Pre-Angled 20N
US Conec manufactures durable, composite, Polyphenylene Sulfide (PPS) based thermoplastic ferrules available with up to 72 fiber holes that terminate 125 micrometer optical fiber. The ferrules are used in conjunction with US Conec’s industry hailed, MTP® brand, MPO type connectors; however, they are also suitable for custom ...
Data Sheet
16505 MT-16 Ferrule With Boot 2x16F Multimode MT Elite
US Conec
Add to watch list
16505 MT-16 Ferrule With Boot 2x16F Multimode MT Elite
US Conec manufactures durable, composite, Polyphenylene Sulfide (PPS) based thermoplastic ferrules available with up to 72 fiber holes that terminate 125 micrometer optical fiber. The ferrules are used in conjunction with US Conec’s industry hailed, MTP® brand, MPO type connectors; however, they are also suitable for custom ...
Data Sheet
16504 MT-16 Ferrule With Boot 1x16F Multimode MT Elite
US Conec
Add to watch list
16504 MT-16 Ferrule With Boot 1x16F Multimode MT Elite
US Conec manufactures durable, composite, Polyphenylene Sulfide (PPS) based thermoplastic ferrules available with up to 72 fiber holes that terminate 125 micrometer optical fiber. The ferrules are used in conjunction with US Conec’s industry hailed, MTP® brand, MPO type connectors; however, they are also suitable for custom ...
Data Sheet
15778 MT Ferrule With Boot 8F Single-Mode APC Pre-Angled
US Conec
Add to watch list
15778 MT Ferrule With Boot 8F Single-Mode APC Pre-Angled
US Conec manufactures durable, composite, Polyphenylene Sulfide (PPS) based thermoplastic ferrules available with up to 72 fiber holes that terminate 125 micrometer optical fiber. The ferrules are used in conjunction with US Conec’s industry hailed, MTP® brand, MPO type connectors; however, they are also suitable for custom ...
Data Sheet
13642 MT Ferrule With Boot 12F Single-Mode APC Pre-Angled
US Conec
Add to watch list
13642 MT Ferrule With Boot 12F Single-Mode APC Pre-Angled
US Conec manufactures durable, composite, Polyphenylene Sulfide (PPS) based thermoplastic ferrules available with up to 72 fiber holes that terminate 125 micrometer optical fiber. The ferrules are used in conjunction with US Conec’s industry hailed, MTP® brand, MPO type connectors; however, they are also suitable for custom ...
Data Sheet
12678 MT Ferrule With Boot 24F Single-Mode APC Pre-Angled
US Conec
Add to watch list
12678 MT Ferrule With Boot 24F Single-Mode APC Pre-Angled
US Conec manufactures durable, composite, Polyphenylene Sulfide (PPS) based thermoplastic ferrules available with up to 72 fiber holes that terminate 125 micrometer optical fiber. The ferrules are used in conjunction with US Conec’s industry hailed, MTP® brand, MPO type connectors; however, they are also suitable for custom ...
Data Sheet
12599 MT Ferrule with boot 48F Multimode PPS
US Conec
Add to watch list
12599 MT Ferrule with boot 48F Multimode PPS
US Conec manufactures durable, composite, Polyphenylene Sulfide (PPS) based thermoplastic ferrules available with up to 72 fiber holes that terminate 125 micrometer optical fiber. The ferrules are used in conjunction with US Conec’s industry hailed, MTP® brand, MPO type connectors; however, they are also suitable for custom ...
Data Sheet
Switchable Adapter
Senko Advanced Components
Add to watch list
Switchable Adapter
Installing this unique adapter in a bulkhead application allows the end user at any time to switch to another adapter interface, in most cases eliminating the need for hybrid cable assemblies. The user simply selects the desired insert according to connector type and fixes it to the adapter base. The Switchable Adapter also allows ...
Data Sheet
ST Attenuators
Senko Advanced Components
Add to watch list
ST Attenuators
A fiber optic attenuator is a passive device used to reduce the amplitude of a light signal without significantly changing the wave form itself. This is often a requirement in Dense Wave Division Multiplexing (DWDM) and Erbium Doped Fiber Amplifier (EDFA) applications where the receiver cannot accept the signal generated from a ...

Specifications
Number Of Channels: Single Channel, Multi Channel
Operating Wavelength Range: 1250-1625nm
Dynamic Attenuation Range (max): 30 dB
Insertion Loss (max): N/A dB
Return Loss (min): 50 dB
Data Sheet
MU Attenuators
Senko Advanced Components
Add to watch list
MU Attenuators
A fiber optic attenuator is a passive device used to reduce the amplitude of a light signal without significantly changing the wave form itself. This is often a requirement in Dense Wave Division Multiplexing (DWDM) and Erbium Doped Fiber Amplifier (EDFA) applications where the receiver cannot accept the signal generated from a ...

Specifications
Number Of Channels: Single Channel, Multi Channel
Operating Wavelength Range: 1250-1625nm
Dynamic Attenuation Range (max): 30 dB
Insertion Loss (max): N/A dB
Return Loss (min): 50 dB
Data Sheet
FC APC Attenuators
Senko Advanced Components
Add to watch list
FC APC Attenuators
A fiber optic attenuator is a passive device used to reduce the amplitude of a light signal without significantly changing the wave form itself. This is often a requirement in Dense Wave Division Multiplexing (DWDM) and Erbium Doped Fiber Amplifier (EDFA) applications where the receiver cannot accept the signal generated from a ...

Specifications
Number Of Channels: Single Channel, Multi Channel
Operating Wavelength Range: 1250-1625nm
Dynamic Attenuation Range (max): 30 dB
Insertion Loss (max): N/A dB
Return Loss (min): 50 dB
Data Sheet
FC Attenuators
Senko Advanced Components
Add to watch list
FC Attenuators
A fiber optic attenuator is a passive device used to reduce the amplitude of a light signal without significantly changing the wave form itself. This is often a requirement in Dense Wave Division Multiplexing (DWDM) and Erbium Doped Fiber Amplifier (EDFA) applications where the receiver cannot accept the signal generated from a ...

Specifications
Number Of Channels: Single Channel, Multi Channel
Operating Wavelength Range: 1250-1625nm
Dynamic Attenuation Range (max): 30 dB
Insertion Loss (max): N/A dB
Return Loss (min): 50 dB
Data Sheet
LC Attenuators
Senko Advanced Components
Add to watch list
LC Attenuators
A fiber optic attenuator is a passive device used to reduce the amplitude of a light signal without significantly changing the wave form itself. This is often a requirement in Dense Wave Division Multiplexing (DWDM) and Erbium Doped Fiber Amplifier (EDFA) applications where the receiver cannot accept the signal generated from a ...

Specifications
Number Of Channels: Single Channel, Multi Channel
Operating Wavelength Range: 1250-1625nm
Dynamic Attenuation Range (max): 30 dB
Insertion Loss (max): N/A dB
Return Loss (min): 50 dB
Data Sheet
SC APC Attenuators
Senko Advanced Components
Add to watch list
SC APC Attenuators
A fiber optic attenuator is a passive device used to reduce the amplitude of a light signal without significantly changing the wave form itself. This is often a requirement in Dense Wave Division Multiplexing (DWDM) and Erbium Doped Fiber Amplifier (EDFA) applications where the receiver cannot accept the signal generated from a ...

Specifications
Number Of Channels: Single Channel, Multi Channel
Operating Wavelength Range: 1250-1625nm
Dynamic Attenuation Range (max): 30 dB
Insertion Loss (max): N/A dB
Return Loss (min): 50 dB
Data Sheet
SC Attenuators
Senko Advanced Components
Add to watch list
SC Attenuators
A fiber optic attenuator is a passive device used to reduce the amplitude of a light signal without significantly changing the wave form itself. This is often a requirement in Dense Wave Division Multiplexing (DWDM) and Erbium Doped Fiber Amplifier (EDFA) applications where the receiver cannot accept the signal generated from a ...

Specifications
Number Of Channels: Single Channel, Multi Channel
Operating Wavelength Range: 1250-1625nm
Dynamic Attenuation Range (max): 30 dB
Insertion Loss (max): N/A dB
Return Loss (min): 50 dB
Data Sheet
FEMTO Grating in Single Mode Acrylate Fiber FFT.FBG.S.00.01
FemtoFiberTec
Add to watch list
FEMTO Grating in Single Mode Acrylate Fiber FFT.FBG.S.00.01
Besides customer specific FBG solutions, FemtoFiberTec offers an attractive range of standardizedfs-written FBGs. Due to the worldwide leading, automated manufacturing technology, FemtoFiberTeccan provide high customer value in terms of quality and cost efficiency.

Specifications
Center Wavelength Range: 1500-1600nm
FBG Length: 6 mm
Reflectivity: >20%
Data Sheet
FEMTO Grating in Single Mode Acrylate Fiber FFT.FBG.S.00.02
FemtoFiberTec
Add to watch list
FEMTO Grating in Single Mode Acrylate Fiber FFT.FBG.S.00.02
Besides customer specific FBG solutions, FemtoFiberTec offers an attractive range of standardizedfs-written FBGs. Due to the worldwide leading, automated manufacturing technology, FemtoFiberTeccan provide high customer value in terms of quality and cost efficiency.

Specifications
Center Wavelength Range: 1500-1600nm
FBG Length: 6 mm
Reflectivity: >50%
Data Sheet
FEMTO Grating in Single Mode Acrylate Fiber FFT.FBG.S.00.03
FemtoFiberTec
Add to watch list
FEMTO Grating in Single Mode Acrylate Fiber FFT.FBG.S.00.03
Besides customer specific FBG solutions, FemtoFiberTec offers an attractive range of standardizedfs-written FBGs. Due to the worldwide leading, automated manufacturing technology, FemtoFiberTeccan provide high customer value in terms of quality and cost efficiency.

Specifications
Center Wavelength Range: 1500-1600nm
FBG Length: 6 mm
Reflectivity: >70%
Data Sheet
FEMTO Grating in Single Mode Polyimide Fiber FFT.FBG.S.01.01
FemtoFiberTec
Add to watch list
FEMTO Grating in Single Mode Polyimide Fiber FFT.FBG.S.01.01
Besides customer specific FBG solutions, FemtoFiberTec offers an attractive range of standardizedfs-written FBGs. Due to the worldwide leading, automated manufacturing technology, FemtoFiberTeccan provide high customer value in terms of quality and cost efficiency.

Specifications
Center Wavelength Range: 1500-1600nm
FBG Length: 6 mm
Reflectivity: >20%
Data Sheet
FEMTO Grating in Single Mode Polyimide Fiber FFT.FBG.S.01.02
FemtoFiberTec
Add to watch list
FEMTO Grating in Single Mode Polyimide Fiber FFT.FBG.S.01.02
Besides customer specific FBG solutions, FemtoFiberTec offers an attractive range of standardizedfs-written FBGs. Due to the worldwide leading, automated manufacturing technology, FemtoFiberTeccan provide high customer value in terms of quality and cost efficiency.

Specifications
Center Wavelength Range: 1500-1600nm
FBG Length: 6 mm
Reflectivity: >50%
Data Sheet